RPQ504IT0 RADIO PROGRAMMER ON/OFF

RPQ504IT0 – 433MHz RADIO PROGRAMMER ON/OFF + TIMER (230V-2000W)

RPQ504IT0 – 433MHz RADIO PROGRAMMER ON/OFF + TIMER (2000W)
For specific uses such as the remote control of external (gardens) and
internal lighting; the remote control of power sockets. Connecting the
radioprogrammer to a light detection device will prevent it from switching
on the lighting system during the daytime.Possibility of memorising up to
1000 user codes. Timer settings: from 1 min. to 23 hrs. 59 min.
All weather box in ABS – IP55.
Overall dimensions 139 x 115 x 44.

If you are an electrician or automation specialist, call +39.0558778855
or write an email to: commerciale@automazione-cancelli.net
to get a quote/offer and an extra discount

RPQ504IT0 RADIO PROGRAMMER ON/OFF + TIMER (2000W)

The RPQ504IT0 radioprogrammer ON/OFF + TIMER , fundamental in every automation,
are available in all the classic Cardin versions: outdoor receivers 12- 24V with display,
with LCD display and 3G/WiFi functions.
230V radio programmers in watertight cases with flip up access covers.
mini receiver units to be installed in appliances which already have a protective casing and slot-in receiver cards for direct
insertion into host appliances designed to receive them.
They are:,
– outdoor receiver with a multi-decoding module S449 – S486 – S504 – S508,
LCD display and 3G-WiFi functions;
– standard outdoor receivers;
– outdoor receivers with display;
– 2-channel mini receivers, slot-in receiver cards;
– 2-channel open collector receiver cards;
– outdoor radio programmers;
– multiprotocol interface.

RECEIVERS WITH LCD DISPLAY AND 3G/WiFi FUNCTIONS

Thanks to the inbuilt 2G-3G or WiFi module, avant-garde software and a highly
efficient signal reception apparatus the receivers allows the remote management
(without range limits) of all installations that require remote control via radio (automatic
entry systems, access control, car-parks etc.).

The appliance is ideally suited to multi-user installations (up to 3000 transmitters can be memorised)
and ones that require frequent upgrading and modification of the codes.
The USB connection, the programming and setting buttons and the efficient display allow the appliance to
be easily configured.
The installation management functions are: transmitter code memorization/
cancellation and programming the function mode for each single output.
The RPQ504IT0 radio programmer for shutters or rolling grillscan manage up to four programmable
channel modules (impulsive/ON-OFF/timer controlled, NO/NC contact type and power on reset).

Technical description of the RADIO PROGRAMMER ON/OFF + TIMER (2000W)

The RRPQ504 radio programmer ON/OFF + TIMER also features a Real Time Clock
which can be used to set the time bands during which the outputs are active.
It also features, the RQM504C1 receiver, as well as a non volatile memory module which can
store up to 100000 relay activation events which may be downloaded during a normal connection and consulted at will.

CARDINTX_SW

The CARDINTX_SW software that can be downloaded from the website www.cardin.
It allows the stored user codes to be managed by means of one of three possible connection methods: direct via USB
cable, using the mobile communications network with a 2G/3G module or using a
WF module.

One or more outputs can be remotely activated over the phone or via
SMS with an installed 2G/3G module or using an App.

Four independent inputs are also available which can be used to monitor external
appliances the status of which can be obtained from the receiver via SMS or an App.
Using the Cardin software it is possible to set the RRPQ508 radioprogrammer for shutters
or rolling grills 4 inputs according to the requirements of the installation.
As soon as an event such as resetting the position status of the door, security devices intervening, presence/absence of power
etc. is detected, the receiver will send a personalised message to the pre-registered
e-mail addresses.
Thanks to this system the 3G receiver becomes a very useful maintenance management tool.

ACCESSORIES RQM504C1 RECEIVER

MCCMORPHM1  : STRIP WITH 1 PROGRAMMABLE RELAY (S504 – S508)
The relay can be set on the RQM504C2 receiver to one of the functions.

CODE MEMORY MODULES
Extractable and furnished with non volatile memory, this EEPROM
contains the system code
MCC24LC64 : 1000-CODE MEMORY MODULE
(RECEIVERS S504D1-S508D1) VERTICAL
ZGB24LC64-I/P : 1000-CODE MEMORY MODULE (S504 – S508)

RSQSPP : SLOT-IN RECEIVER ADAPTOR
Allows you to use the AMP 10-way receivers card connector as a
standard terminal block.

ANS400    : AERIAL FOR 433MHz RECEIVERS
ANQ800-1 : AERIAL FOR 868MHz RECEIVERS
ZVCRG58  : COAXIAL CABLE RG58 (per metre)

ANSKITGSMWF10 : KIT AERIAL EXTENSION 2G – 3G WiFi 10m SMA-M
ANSKITGSMWF5  : KIT AERIAL EXTENSION 2G – 3G WiFi 5m SMA-M

XRP03 : LITHIUM BATTERY 3V (2 X CR2032)

QUARTZ RECEIVER/TRANSCEIVER MODULE (433MHz – 868MHz)
Superheterodyne in FM with a digital filter.
Unidirectional (DG) and bidirectional (DG) versions.
RF module without decoder for the reception of digital signals.
Voltage: 5Vdc – Electrical input: 15mA.
Overall dimensions 40 x 20 x 13.
JRF433QFMDG1
JRF868QFMDG1
JRF433QFMBD0
JRF868QFMBD0